Skip to content

Next Venture Aluminum Inner Fender Liners in one listing. Choose your Jeep / position / style; each choice is a specific Next Venture kit, described below.

JL/JT Aluminum Front Inner Fender Liners


JL/JT Aluminum Front Inner Fender Liner

CAD Designed with maximum tire clearance and suspension up travel in mind!
  • Laser Cut and Precision CNC Formed
  • 0.090" 5052 Aluminum Construction
  • Vented to increase airflow to engine bay
  • 2 piece design with 1/4 Turn Fasteners for Fast Removal and Maintenance Access
  • Arrives ready to powder coat

The Details


The factory black plastic "splash guards" you'll find in the front wheel openings of your JL and JT can leave a bit to be desired. Our new front inner fender liners are designed to work with our aluminum front fender flares - though they can be installed independently if desired.

Quick accessibility to the engine bay for maintenance is possible thanks to 1/4 turn "dzus" fasteners. Having wired up a few lights, winches, and performing upgrades to our steering system have taught us the benefits of that quick, wide open access through the inner fender areas of our JL and JT.

Vents on both sides allow heat to escape the engine bay near the top of each inner fender liner, to help make up for those larger tires and extra gear on big climbs. The laser cut honeycomb pattern is small enough to keep rocks and most debris out while allowing for airflow.

These are laser cut, CNC formed and hand welded from 0.09" thick 5052-H32 Aluminum; a bit thicker then most 0.06" panels on the market, to give them a bit of extra rigidity. Installation does require drilling, but thanks to the rigidity of the panels and mounting locations on the body, these are entirely body mounted and do not require any fasteners or brackets to be tied into the frame rails of your JL; allowing your body mounts to flex properly without putting any load on your fender liners.

We have been collecting 3D scan data from multiple Jeeps over the past couple of years and have CAD designed these inner fender liners to fit as closely as possible to what sits in your engine bay -- whether your JL or JT is a 3.6 V6, 2.0 Turbo, 392 Hemi, EcoDiesel, or even 4xE -- allowing us to retain as much tire clearance and suspension up travel as possible!

Please note, that the EcoDiesel and 392 models have a large factory wiper fluid reservoir that does eat up a lot of tire clearance -- both with factory "splash guards" and any aftermarket inner fender liner that retains the factory reservoir. If you remove or relocate this reservoir, you can use the higher clearance version of the inner fender liner that is used for the 3.6/2.0 gas models and make a lot more room for 38" and larger tires without complications from rubbing or limiting suspension up-travel.

JL/JT Aluminum Front Inner Fender Liners (Rock Krawler Coilover)


JL/JT Aluminum Front Inner Fender Liner (Rock Krawler Coilover Specific)

CAD Designed with maximum tire clearance and suspension up travel in mind!
  • Laser Cut and Precision CNC Formed
  • 0.090" 5052 Aluminum Construction
  • Vented to increase airflow to engine bay
  • 2 piece design with 1/4 Turn Fasteners for Fast Removal and Maintenance Access
  • Arrives ready to powder coat

The Details

The factory black plastic "splash guards" you'll find in the front wheel openings of your JL and JT can leave a bit to be desired. Our new front inner fender liners are designed to work with our aluminum front fender flares - though they can be installed independently if desired.

Quick accessibility to the engine bay for maintenance is possible thanks to 1/4 turn "dzus" fasteners. Having wired up a few lights, winches, and performing upgrades to our steering system have taught us the benefits of that quick, wide open access through the inner fender areas of our JL and JT.

Vents on both sides allow heat to escape the engine bay near the top of each inner fender liner, to help make up for those larger tires and extra gear on big climbs. The laser cut honeycomb pattern is small enough to keep rocks and most debris out while allowing for airflow.

These are laser cut, CNC formed from 0.09" thick 5052-H32 Aluminum; a bit thicker then most 0.06" panels on the market, to give them a bit of extra rigidity. Installation does require drilling, but thanks to the rigidity of the panels and mounting locations on the body, these are entirely body mounted and do not require any fasteners or brackets to be tied into the frame rails of your JL; allowing your body mounts to flex properly without putting any load on your fender liners.

We have been collecting 3D scan data from multiple Jeeps over the past couple of years and have CAD designed these inner fender liners to fit as closely as possible to what sits in your engine bay -- whether your JL or JT is a 3.6 V6, 2.0 Turbo, 392 Hemi, EcoDiesel, or even 4xE -- allowing us to retain as much tire clearance and suspension up travel as possible!

Please note, that the EcoDiesel and 392 models have a large factory wiper fluid reservoir that does eat up a lot of tire clearance -- both with factory "splash guards" and any aftermarket inner fender liner that retains the factory reservoir. If you remove or relocate this reservoir, you can use the higher clearance version of the inner fender liner that is used for the 3.6/2.0 gas models and make a lot more room for 38" and larger tires without complications from rubbing or limiting suspension up-travel.

JL Aluminum Rear Inner Fender Liners (Standard)


JL Aluminum Rear Inner Fender Liner (Standard)

  • CAD Designed with maximum tire clearance and suspension up travel in mind - without any trimming required! Need more clearance than that and you're willing to trim? Check out our 40"+ Tire Version!
  • Laser Cut and Precision CNC Formed from 0.09" 5052 Aluminum
  • Quick bolt together assembly required for initial installation
  • 1/4 Turn Fasteners for Fast Removal and Maintenance Access
  • Arrives ready to powder coat if desired
  • Sold as 1 pair (left/right)
  • Designed to work with shocks from Factory to aftermarket large body with multiple bypass/reservoir setups
  • Designed to work with factory shock mounts or RKs extended shock/coilover rear mounts (see Shock Compatibility below)

The Details


The factory black plastic "splash guards" you'll find in the wheel openings of your JL can leave a bit to be desired. Our new rear inner fender liners are designed to be installed as a stand-alone item, or compatible with our JL Rear High Line Fender Flares.

Our rear fender liners are laser cut in house from 0.09" thick 5052 Aluminum - which means they are 30% thicker than most 0.06" (16 Gauge) liners on the market, offering a bit more rigidity.

Quick accessibility to is possible thanks to 1/4 turn "dzus" fasteners.

Picture above shows inner fender liner installed alongside our JL rear fender delete. Rear fender delete is sold separately and not included.

Initial installation requires a quick bolt together assembly, and all required hardware is included. Installation requires ZERO drilling, but thanks to the rigidity of the panels and mounting locations on the body, these are entirely body mounted and do not require any fasteners or brackets to be tied into the frame rails of your JL; allowing your body mounts to flex properly without putting any load on your fender liners.

Shock Compatibility

We have been collecting 3D scan data from multiple Jeeps over the past couple of years. This has allowed to CAD design these rear inner fender liners to fit with shocks from factory to aftermarket big body shocks with multiple bypasses with reservoirs; using factory mounts or even the relocated and extended shock/coilover mounts from Rock Crawler Suspension. The short of list of compatible shocks include factory, ADS, Bilstein, King, Falcon, Fox, and Rock Krawler/RRD Shocks. There are always new shock configurations coming out for the ever popular JL platform, so if you have any questions don't hesitate to reach out to us and ask if another new option fits!

4xE Compatibility

The Jeep Wrangler 4xE has additional lines on the rear passenger side leading to the evap canister just in front of the tail lamp; and these extra components are routed through the wheel well where this liner is installed. We have confirmed with a test fit that these DO work without modification on the 4xE PHEV models!

Axle Compatibility: Rubicon vs Sport Axles

Above: A "Willys" trim JL flexing out with the rear inners installed. This JL is equipped with the narrow JL "Sport" axles, and wheel spacers. Some trimming may be required with narrow/Non-Rubicon axles in applications with little to no lift, due to the narrow axle width.

These are designed for maximum up-travel, however they are designed with Rubicon width tires/wheels in mind. If you are running JL "Sport"/Non-Rubicon width axles, either additional offset or some trimming may be required to clear the rear tires at full stuff.

If you are running Rubicon width or even wider axles, clearance is typically increased between the tire and inner fender liner, and should result in no rubbing and no modifications required.

JL Aluminum Rear Inner Fender Liners (40"+)


JL Aluminum Rear Inner Fender Liner (40 Inch Plus) for Big Tires

Looking to mount up 40" or larger tires on your JL? We designed this fender liner specifically to match our 40"+ Steel brackets (which are INCLUDED) that tie everything in the body back together after you do trimming to maximize clearance. Don't want to do any trimming? Check out our standard Rear Inner Fender Liners here!

  • CAD Designed with maximum tire clearance and suspension up travel in mind (Trimming IS REQUIRED for this version!)
  • Tested specifically with 40"-42" tires for maximum clearance and trimming without removing structural integrity in the JL body.
  • Allows for 3/8" wheelbase stretch to the rear - so you only have to trim the back of the wheel well; not the front. This prevents you from getting any water intrusion into the passenger compartment/JL tub!
  • Laser Cut and Precision CNC Formed from 0.09" 5052 Aluminum
  • Quick bolt together assembly required for initial installation
  • Arrives ready to powder coat if desired
  • Sold as 1 pair (left/right)
  • Designed to work with shocks from Factory to aftermarket large body with multiple bypass/reservoir setups
  • Designed to work with factory shock mounts or RKs extended shock/coilover rear mounts (see Shock Compatibility below)

The Details


The factory black plastic "splash guards" you'll find in the wheel openings of your JL can leave a bit to be desired. Our new rear inner fender liners can be installed with factory fender flares, our JL Rear Fender deletes and are also compatible with our JL Rear High Line Fender Flares!

Our rear fender liners are laser cut in house from 0.09" thick 5052 Aluminum - which means they are 30% thicker than most 0.06" (16 Gauge) liners on the market, offering a bit more rigidity.


Above: How much you'll be trimming out. The "Before" shot. Note that we have temporarily removed the EVAP canister to prevent any damage to it during trimming!
Initial installation requires a quick bolt together assembly, and all required hardware is included. Installation requires DRILLING and CUTTING.

Above: "After" the trimming. Shown with Rear Fender Flare partially installed - sold separately and not included.
It also should be completed in conjunction with our 40"+ Kit Steel Brackets that insert into the body, and tie everything back in together since you've cut out some of your pinch welds that previously bonded multiple sheet metal bodies together.
Above: The 40"+ Kit Steel Brackets. This is what ties the body back together after trimming!


Above: The 40"+ Kit Steel Brackets installed.
Thanks to the rigidity of the panels and mounting locations on the body, these are entirely body mounted and do not require any fasteners or brackets to be tied into the frame rails of your JL; allowing your body mounts to flex properly without putting any load on your fender liners!


Above: The finished product. The 40"+ Rear Inner Fender Liners, 40"+ Kit Steel Bracket installed along side a JL Rear Fender Flare (sold separately.)

Shock Compatibility

We have been collecting 3D scan data from multiple Jeeps over the past couple of years. This has allowed to CAD design these rear inner fender liners to fit with shocks from factory to aftermarket big body shocks with multiple bypasses with reservoirs; using factory mounts or even the relocated and extended shock/coilover mounts from Rock Crawler Suspension. The short of list of compatible shocks include factory, ADS, Bilstein, King, Falcon, Fox, and Rock Krawler/RRD Shocks. There are always new shock configurations coming out for the ever popular JL platform, so if you have any questions don't hesitate to reach out to us and ask if another new option fits!

4xE Compatibility

The Jeep Wrangler 4xE has additional lines on the rear passenger side leading to the evap canister just in front of the tail lamp; and these extra components are routed through the wheel well where this liner is installed. We have confirmed with a test fit that these DO work without modification on the 4xE PHEV models!

Axle Compatibility: Rubicon vs Sport Axles

Above: A "Willys" trim JL flexing out with the rear inners installed. This JL is equipped with the narrow JL "Sport" axles, and wheel spacers. Some trimming may be required with narrow/Non-Rubicon axles in applications with little to no lift, due to the narrow axle width.

These are designed for maximum up-travel, however they are designed with Rubicon width tires/wheels in mind. If you are running JL "Sport"/Non-Rubicon width axles, either additional offset or some trimming may be required to clear the rear tires at full stuff.

If you are running Rubicon width or even wider axles, clearance is typically increased between the tire and inner fender liner, and should result in no rubbing and no modifications required.

Installation Video

Watch the full install, start to finish, before you cut:

JT Aluminum Rear Inner Fender Liners


JT Aluminum Rear Inner Fender Liner

  • CAD Designed with maximum tire clearance and suspension up travel in mind
  • Laser Cut and Precision CNC Formed from 0.09" 5052 Aluminum
  • Quick bolt together assembly required for initial installation
  • 1/4 Turn Fasteners for Fast Removal and Maintenance Access (4 per side)
  • Arrives ready to powder coat if desired or can be left as natural aluminum finish
  • Sold as 1 pair (left/right)
  • NOT COMPATIBLE WITH DIESEL MODELS

The Details


The factory black plastic "splash guards" you'll find in the wheel openings of your JT can leave a bit to be desired. Our new rear inner fender liners are designed to be installed as a stand-alone item with your factory flares, and are also compatible with our JT Rear High Line Fender Flares.

Our rear fender liners are laser cut in house from 0.09" thick 5052 Aluminum - which means they are 30% thicker than most 0.06" (16 Gauge) liners on the market, offering a bit more rigidity.

Installation


Quick accessibility to is possible thanks to 1/4 turn "dzus" fasteners. Initial installation requires a quick bolt together assembly, and all required hardware is included. Installation uses existing factory holes in your factory JT bed. If you are using these with factory flares, a few of the factory clips that hold the flares in will need to be removed as they will be fastened using some of the included hardware in shared holes on the factory sheet metal.

An electrical harness does need to be relocated, however it simply pops out of it's original location, and into the included aluminum bracket that bolts on to the JT rear frame. The evap vent on the driver side of the JT at the front of the wheel well is also relocated ever so slightly in the interest of tire clearance using included hardware.

Shock Compatibility

Unlike the front fender liners, and most Wrangler rear liners, the JT liners don't typically effect shock compatibility due to the shape of the JT frame and shock mounts.

JT Aluminum Rear Inner Fender Liners - Anti-Rock Compatible


JT Aluminum Rear Inner Fender Liner - Anti-Rock Compatible

  • Compatible with JT rear Anti-Rock Sway Bar
  • CAD Designed with maximum tire clearance and suspension up travel in mind
  • Laser Cut and Precision CNC Formed from 0.09" 5052 Aluminum
  • Quick bolt together assembly required for initial installation
  • 1/4 Turn Fasteners for Fast Removal and Maintenance Access (4 per side)
  • Arrives ready to powder coat if desired or can be left as natural aluminum finish
  • Sold as 1 pair (left/right)
  • NOT COMPATIBLE WITH DIESEL MODELS

The Details


The factory black plastic "splash guards" you'll find in the wheel openings of your JT can leave a bit to be desired. Our new rear inner fender liners are designed to be installed as a stand-alone item with your factory flares, and are also compatible with our JT Rear High Line Fender Flares.

Our rear fender liners are laser cut in house from 0.09" thick 5052 Aluminum - which means they are 30% thicker than most 0.06" (16 Gauge) liners on the market, offering a bit more rigidity.

Installation


Quick accessibility to is possible thanks to 1/4 turn "dzus" fasteners. Initial installation requires a quick bolt together assembly, and all required hardware is included. Installation uses existing factory holes in your factory JT bed. If you are using these with factory flares, a few of the factory clips that hold the flares in will need to be removed as they will be fastened using some of the included hardware in shared holes on the factory sheet metal.

An electrical harness does need to be relocated, however it simply pops out of it's original location, and into the included aluminum bracket that bolts on to the JT rear frame. The evap vent on the driver side of the JT at the front of the wheel well is also relocated ever so slightly in the interest of tire clearance using included hardware.

Shock Compatibility

Unlike the front fender liners, and most Wrangler rear liners, the JT liners don't typically effect shock compatibility due to the shape of the JT frame and shock mounts.

"This content is currently unavailable."
"This content is currently unavailable."
"This content is currently unavailable."
"This content is currently unavailable."